雙組份打膠機的注意事項
Points for attention of two component glue machine
雙組份涂膠機是出產中空、幕墻玻璃的專用設備，可一次完成二道密封中A、B組份混合與涂膠。適用配比精度高的膠種，滿足玻璃深加工企業高、高合格率流水線作業的出產需求，是大規模出產高級優質中空玻璃及玻璃幕墻產品的一種抱負的配套設備。
Two-component gluing machine is a special equipment for producing hollow and curtain wall glass. It can mix and glue components A and B in two seals at one time. It is suitable for mixing rubber with high precision and meets the production demand of high efficiency and high qualified rate pipeline operation in glass deep processing enterprises. It is an ideal matching equipment for large-scale production of high-quality hollow glass and glass curtain wall products.
1.因為雙組份密封膠的固化需要一定時刻，因而，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. Because the curing of the two-component sealant takes a certain time, the glass coated with the two-component sealant should be moved horizontally and gently.
2.A組.B組份膠應保持清潔，嚴防異物進入膠中。
Group 2.A.B component should be kept clean and foreign matter should be strictly protected.
3.在接連工作過程中，膠槍每次停止工作時刻一般不得超過20分鐘，否則，運用A組份膠沖出悉數混合膠，直至單一的A組份膠從槍口排出停止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, use component A glue to punch out all the mixed glue until a single component A glue is discharged from the muzzle of the gun.

4.高壓膠管不得強行擠壓.彎曲，避免影響體系正常工作。
4. high pressure hose should not be forced to press. Bend to avoid affecting the normal work of the system.
5.混膠器應經常保持疏通，以確保杰出的出膠作用。如遇阻塞狀況，可用丙酮浸泡后清洗。主張每5組清洗一次。
5. rubber mixer should be maintained regularly to ensure excellent glue production. In case of obstruction, acetone can be soaked and cleaned. It is advocated that every 5 groups be cleaned once.
6.當膠槍長時刻不用時（超過一周），應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗潔凈。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned by solvent.
7.不同雙組份膠出產廠家所出產的膠內含雜質數量不同，根據實際狀況清晰B組分的過濾網及單向止回閥，主張每兩組清洗一次。
7. The amount of impurities in the gum produced by different two-component gum manufacturers is different. According to the actual situation, the filters and check valves with clear component B should be cleaned once for each two groups.
8.任何因膠體固化所形成的膠槍.管路或整機的毛病，一概不在保修范圍之內。
8. Any defect of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期給各泵的加油口加油，應確保油霧器內不斷油。
9. regular refueling of each pump should ensure that the oil mist is constantly oil.
本文由濟南昌盛機械http://www.dgjiaxing.com.cn整理,我們將為您提供新的雙組份打膠機知識，有興趣的朋友可以關注我們，謝謝!!
This article is organized by Jinan Changsheng Machinery http://www.dgjiaxing.com.cn. We will provide you with new knowledge of two-component gluing machine. Interested friends can pay attention to us. Thank you!