全自動鋁條折彎機作為金屬加工領域的關鍵設備，在長期高負荷運轉后，可能出現精度下降、部件磨損、系統故障等問題。這些問題不僅影響生產效率，還可能引發安全隱患。

　　As a key equipment in the field of metal processing, the fully automatic aluminum strip bending machine may experience problems such as decreased accuracy, component wear, and system failures after long-term high load operation. These issues not only affect production efficiency, but may also pose safety hazards.

　　一、機械系統磨損與校正

　　1、 Mechanical system wear and correction

　　同步帶松弛：長期運轉后，傳動同步帶可能因拉伸變形導致折彎角度偏差。需定期檢查張緊輪，使用激光干涉儀校準同步帶張力，偏差超過5%時需更換。

　　Slack of synchronous belt: After long-term operation, the transmission synchronous belt may experience bending angle deviation due to stretching deformation. Regularly check the tensioning wheel and calibrate the synchronous belt tension using a laser interferometer. If the deviation exceeds 5%, it needs to be replaced.

　　導軌間隙擴大：X/Y軸導軌磨損會導致定位精度降低。采用電感測微儀檢測間隙，超過0.02mm時需重新刮研導軌面，并補充鋰基潤滑脂。

　　Expansion of guide rail clearance: Wear of X/Y-axis guide rails can lead to a decrease in positioning accuracy. Use an inductive micrometer to detect the gap. If it exceeds 0.02mm, the guide rail surface needs to be re scraped and lubricated with lithium based grease.

　　模具損耗：沖壓次數達10萬次后，模具刃口可能出現卷邊。需用投影儀檢測刃口輪廓，采用線切割工藝修復，磨損量超0.5mm時整體更換。

　　Mold wear: After 100000 stamping cycles, the cutting edge of the mold may have curled edges. It is necessary to use a projector to detect the contour of the cutting edge, repair it using wire cutting technology, and replace it as a whole when the wear exceeds 0.5mm.

　　二、液壓系統維護策略

　　2、 Hydraulic system maintenance strategy

　　油液污染：液壓油每2000小時需檢測污染度，NAS 1638等級超過9級時需過濾或更換。系統回油管路應增設磁性過濾器，捕捉金屬磨屑。

　　Oil contamination: Hydraulic oil should be tested for contamination every 2000 hours, and if the NAS 1638 level exceeds level 9, it should be filtered or replaced. Magnetic filters should be added to the system's return oil pipeline to capture metal debris.

　　密封件老化：液壓缸O型圈使用3年后可能硬化泄漏。需定期檢查缸體滲油情況，更換為氟橡膠材質密封件，耐溫范圍擴展至-20℃~200℃。

　　Seal aging: The O-ring of the hydraulic cylinder may harden and leak after 3 years of use. Regularly check the oil leakage situation of the cylinder block, replace it with fluororubber material seals, and extend the temperature resistance range to -20 ℃~200 ℃.

　　閥組卡滯：比例伺服閥因油液氧化可能引發動作遲滯。每半年進行閥芯清洗，使用航空煤油超聲波清洗，并重新標定零位電流。

　　Valve group stuck: The proportional servo valve may experience action delay due to oil oxidation. Clean the valve core every six months, use aviation kerosene ultrasonic cleaning, and recalibrate the zero position current.

　　三、電氣系統優化方案

　　3、 Optimization plan for electrical system

　　編碼器漂移：旋轉編碼器使用5年后可能產生累計誤差。采用雙編碼器冗余設計，主從編碼器信號比對，偏差超0.1°時觸發報警。

　　Encoder drift: Rotary encoders may experience cumulative errors after 5 years of use. Adopting a dual encoder redundancy design, the master-slave encoder signals are compared, and an alarm is triggered when the deviation exceeds 0.1 °.

　　PLC程序冗余：長期運行可能導致程序位丟失。需建立程序鏡像備份，使用EEPROM存儲關鍵參數，每月進行CRC校驗。

　　PLC program redundancy: Long term operation may result in loss of program bits. It is necessary to establish a program image backup, store key parameters using EEPROM, and perform CRC verification on a monthly basis.

　　伺服電機溫升：連續工作8小時后電機溫度可能超80℃。優化驅動器PID參數，增設軸流風機強制冷卻，環境溫度超過40℃時暫停運行。

　　Servo motor temperature rise: After continuous operation for 8 hours, the motor temperature may exceed 80 ℃. Optimize the PID parameters of the drive, add axial flow fan for forced cooling, and suspend operation when the ambient temperature exceeds 40 ℃.

　　四、控制系統升級路徑

　　4、 Control system upgrade path

　　人機界面優化：老式電阻屏易產生誤操作。升級為電容式觸摸屏，增加手勢縮放功能，便于模具庫調用。

　　Human machine interface optimization: Old style resistive screens are prone to misoperation. Upgrade to a capacitive touch screen and add gesture zoom function for easy access to the mold library.

　　折彎算法迭代：傳統補償算法難以應對高強鋁合金。引入神經網絡補償模型，通過200組歷史數據訓練，使角度誤差控制在±0.3°以內。

　　Bending algorithm iteration: Traditional compensation algorithms are difficult to cope with high-strength aluminum alloys. Introduce a neural network compensation model and train it with 200 sets of historical data to control the angle error within ± 0.3 °.

　　遠程診斷接口：增設4G模塊實現遠程維護。專家系統可讀取PLC寄存器數據，故障定位時間縮短。

　　Remote diagnostic interface: Add 4G module to achieve remote maintenance. Expert systems can read PLC register data, reducing fault location time.

　　備件生命周期管理：對電磁閥、接近開關等易損件實施三級庫存管理，根據MTBF數據動態調整安全庫存量。

　　Spare parts lifecycle management: Implement three-level inventory management for vulnerable parts such as solenoid valves and proximity switches, and dynamically adjust safety stock levels based on MTBF data.

　　通過上述系統性維護策略，可使全自動鋁條折彎機保持穩定運行狀態，設備綜合效率（OEE）提升，維護成本降低。實踐表明，實施預防性維護的設備，其使用壽命可延長，故障間隔時間增加。隨著工業互聯網技術的發展，預測性維護將成為主流，通過振動監測、油液分析等手段，實現從“定期檢修”到“按需維護”的轉變。

　　Through the above systematic maintenance strategy, the fully automatic aluminum strip bending machine can maintain stable operation, improve overall equipment efficiency (OEE), and reduce maintenance costs. Practice has shown that equipment implementing preventive maintenance can extend its service life and increase the interval between failures. With the development of industrial Internet technology, predictive maintenance will become the mainstream. Through vibration monitoring, oil analysis and other means, the transformation from "regular maintenance" to "on-demand maintenance" will be realized.

　　本文由全自動鋁條折彎機友情奉獻.更多有關的知識請點擊:http://www.dgjiaxing.com.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from glass coating machine equipment For more information, please click: http://www.dgjiaxing.com.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message